How To Replace Tub Spout Diverter

Look over the underside of the spout with a flashlight looking for a small screw that may hold the spout on the water pipe. When a diverter valve is working properly water only flows out of either the tub spout.

How To Insert Bathtub Faucet Handle Diverter Stem Youtube

There should be an Allen wrench screw in the bottom end of the bathtub spout.

How to replace tub spout diverter. If your Tub Spout is hard to remove you may need to use the end of a hammer or large wrench to help loosen while turning. Continue to hand tighten the tub spout until the spout is firmly against the finished wall surface. They all look the same to me 3.

Turn the screwdriver counterclockwise. Remove the tub spout type by rotating the spout counterclockwise and unscrew it from the spout pipe. Step 2 - Repair the Faulty Diverter.

Now you can take the loosened tub spout and remove it completely. Take care to not damage the O-ring on the brass adapter. Tighten the spout so that the opening is aligned straight up and down.

It is revolting to spend 8 to get a 5 cent washer but you do what you have to. Dispose of excess parts. First the tub spout diverter can wear out so it no longer blocks the water flow and sends water to the shower head.

After fully loosening the set screw turn the tub spout gently to break the seal and pull it toward you to remove it. Snap the tabs of the diverter gate 4 onto the lift rod 1. Go through the diverter assembly and lubricate all moving parts to ensure proper motion and use.

Insert a large screwdriver or the handle of a wood hammer into spout using the tool as a lever to rotate the spout in a counterclockwise direction. Step by step instructions for how you can change a tub diverter spout in your bathroomThis should have been a home project that took less than 5 minutes bu. Install the New Spout Thread the new spout onto the stub-out pipe slowly by hand at first.

Use the edge of a flat-bladed screwdriver to pop off the diverter handle screw cover. Remove the plasic diverter and rubber cup washer from both old and new spouts. Pull out the old metal shower diverter and slip the new one in its place.

Take a heavy-duty screwdriver and insert it into the opening of the spout. IPS Threaded - Threaded directly onto the pipe from the wall. There will be a small hole in the bottom of the tub spout if you see a screw you have a CC Slip Fit tub spout.

Unthread the tub spout counter-clockwise to remove. Remove the screw on the underside of the spout if one is present using an appropriately sized Allen wrench. Install the new nipple Wrap both ends of the new nipple with thread tape and screw it into the fitting inside the wall.

Using a little force you can pull it off easily. Just insert the handle into the opening of the Tub Spout for leverage. Remove the bathtubs spout to replace it and the diverter.

Install a new tub diverter spout with the same style connection ie an allen set screw at the rear. Turning counterclockwise remove the old Tub Spout. To avoid scratching the finish protect the spout by wrapping a rag around it before attaching the wrench to finish tightening the spout.

If there is no screw you have an IPS threaded tub spout. The diverter gate 4 goes into the bottom of the tub spout 2 with the installed washer 3 facing the wall. Locate the rubber washer and replace.

If you have a hard to replace tub spout do the following. Turn the faucet upward and pry apart the plastic prongs. Seal around it with silicone caulk and screw on the new spout.

Step 4 - Replace the Washer. Step 3 - Replace Diverter If Necessary. Bathtub spouts can go bad in three ways.

If your Tub Spout has a set screw holding it in place be sure to remove that prior to rotating the Spout off. This can usually be done by pulling the tub spout towards yourself. Thread the tub spout onto the brass adapter hand tight.

Unthread and remove the spout. There should not be any space left between the spout and the wall. Buy a cheap diverter spout 8 2.

It is important that all parts work without friction to ensure proper movement of all parts. Slide the lift rod 1 through the hole in the top of the spout 2. Then the bathtub spout will be loosely fitted with the copper tubing in the wall.

Now you can turn. Sometimes however it does take a bit of unscrewing with a tool as well. Hold the diverter spout firmly against the shower wall or as far as it.

At first you have to loosen it up with the help of a screwdriver. This removes the potential for leakage. A diverter is used in combination bathshower units to direct flow either to the bathtub spout or to the showerhead.

Step 2 Examine the diverter handle. We will now walk you through the process of replacing the bathtub spout shower diverter. Next reinsert the diverters underside portion by first putting in the spring and then the black washer.

The action shifts the spout and.

How To Replace A Bathtub Spout Diy Family Handyman